Huntsman Araldite 2050: 2-Minute and Extreme-Cold-Set, Wet & Underwater MMA Adhesive
Need Datasheets?
Click Here to visit our Datasheet Server (TDS, SDS, Fact Sheets, Selector Guides, etc)
Product Description
Araldite® 2050 A/B is a two component, methacrylate general purpose adhesive for rapid assembly operations on a wide range of substrates. This adhesive provides excellent strength even when used at very low temperature and in moist conditions. It is the perfect choice for repair jobs in very difficult conditions.
And Araldite 2050 sets in very cold conditions, setting in as low as -20c / -4f , and is perfect for winter applications.
Features
- Ultra-fast curing from -20°C to 25°C (-4°F to 75°F)
- Sets / Dries / Cures completely underwater, high moisture and high humidity
- Excellent bond to a wide range of plastics, composites and metals
- Minimum surface cleaning or pretreatment needed
- Suitable for service at temperatures up to 120°C (250°F)
- Excellent ageing and weathering resistance
- Thixotropic Gel, Non-Sagging, Non-Dripping, Non-Running
- Work Life: 1-2 minutes, Fast Setting
- Handling Strength Time: 9 minutes (Handling strength is time to about 25% cure. hard and strong enough to be generally handled.
| Cure times to reach minimum shear strength (sandblasted aluminum) | |||||||||||||
| Temperature | -20°C (-4°F) | -10°C (14°F) | 0°C (32°F) | 10°C (50°F) | 23°C (73°F) | ||||||||
| >1MPa (145 psi) | 4 h | 90 min | 40 min | 12 min | 9 min | ||||||||
| >10MPa (1,450 psi) | 8 h | 3 h | 1 h | 20 min | 13 min | ||||||||
Pretreatment: The strength and durability of a bonded joint are dependent on proper treatment of the surfaces to be bonded. At the very least, joint surfaces should be cleaned with a good degreasing agent such as acetone, isopropanol (for plastics) or other proprietary degreasing agents in order to remove all traces of oil, grease and dirt. Low-grade alcohol, gasoline, or paint thinners should never be used. The strongest and most durable joints are obtained by either mechanically abrading or chemically etching (“pickling”) the degreased surfaces. Abrading should be followed by a second degreasing treatment.
Araldite® 2050 A/B structural adhesive is available in cartridges incorporating mixers and can be applied as ready to use adhesive with the aid of the tool recommended by Huntsman Advanced Materials.
Application of Adhesive: This system is available in cartridges incorporating mixers and can be applied as ready to use adhesive with the aid of the tool recommended by Huntsman Advanced Materials. The resin/hardener mix may be applied manually or robotically to the pretreated and dry joint surfaces. Huntsman's technical support group can assist the user in the selection of a suitable application method as well as suggest a variety of reputable companies that manufacture and service adhesive dispensing equipment. A layer of adhesive 0.25 mm thick will normally impart the greatest lap shear strength to the joint. The joint components should be assembled and secured in a fixed position as soon as the adhesive has been applied. For more detailed explanations regarding surface preparation and pretreatment, adhesive joint design, and the dual cartridge dispensing system, visit www.aralditeadhesives.com.
Temperature of application: the recommended temperature application range is -20°C to 25°C (-4°F to 77°F). If the adhesive is used at a temperature above 25°C (77°F), because of the fact reaction, the viscosity will increase so rapidly that a good wetting of the substrate will be difficult to achieve. Therefore above 25°C (77°F), the performance of the bond may be limited. For higher application temperatures, the Araldite® 2051 may be preferred.
WARNING! The cure reaction can generate a high amount of heat, it is not recommended to mix large amounts of material at room temperature
Storage: Araldite® 2050 A/B Adhesive should be stored in a dry place, in the original sealed containers, at temperatures between 2°C to 8°C (36°F to 46°F). Under these storage conditions, the product has a shelf life of 18 months from date of shipment from Huntsman. The product should not be exposed to direct sunlight. The product may be placed at room temperature before use, the total time at room temperature should not exceed 6 months. Long term exposure above 25°C will reduce the shelf life of the product. The product should be never frozen.
For additional information, consult the Technical Data Sheet (TDS) and Safety Data Sheet (SDS).